Shutdown the VM, and identify where the VMX config file is located To find the VMX: Right-click over the VM and select Edit Settings... Sysprep deletes drive letter mappings during customization If you choose customization options and the destination virtual machine fails at a Please Wait screen after the second sysprep reboot, you need to The number of LVM logical volumes per volume group is limited to 12 for powered on Linux sources During the conversion of powered on Linux machines, Converter Standalone converts LVM volume During conversion of powered on Linux machines, Converter Standalone does not recognize Linux source volumes if they are mapped directly on a hard disk Workaround: Linux source volumes that are not http://webinweb.net/unable-to/vmware-converter-windows-2008-r2-unable-to-obtain-hardware-information.html
The video has my comments as text on the screen and you can pause anytime when needed. Like Show 0 Likes (0) Actions 23. For more information about the operating systems supported by Converter Standalone and other system requirements, see the VMware vCenter Converter Standalone User's Guide. VMware Converter P2V / Cold Clone Process How to inject storage RAID controller drivers into...
Troubleshooting ESXi slow boot up times with boot ... If you try to convert the source without reconfiguration, the conversion succeeds but the destination cannot boot. Re: "Unable to Obtain Hardware information for the selected machine" POCEH Aug 8, 2014 12:44 AM (in response to bupt_Henry) Could you upload the log bundle?
You cannot copy running conversion or configuration jobs If you open the Copy As New wizard for a running configuration or conversion job when the source is a virtual machine or VMware ESXi 4.1 slow boot up seemingly stuck at: v... Quick note about P2V with Cold Clone WinPE CD and ... Vmware Converter 5.5 Unable To Obtain Hardware Information Browse to the Temp folder of the current user (for example, C:\Documents and Settings\"username"\Local Settings\Temp) and click OK.
Message Author Comment by:R_M_Ron ID: 371280032011-11-13 Already checked the VM Settings on OS type. Vmware Converter V2v Unable To Obtain Hardware Information For The Selected Machine The WSDL that defines the API available on Converter server. Re: "Unable to Obtain Hardware information for the selected machine" Plamen Aug 11, 2014 2:08 AM (in response to bupt_Henry) 1. Reply Subscribe RELATED TOPICS: Is VMware vCenter Converter Standalone Compatible with ESXi 5.5 Convert Physical Server to VMDK physical server to virtual using VMware ESXi 4 Replies Anaheim
The sample code includes Java and C# source code files. Vmware Converter 6 Unable To Obtain Hardware Information That worked for me! If the hardware configuration of the source machine is modified while the Conversion wizard is open, you need to restart the conversion wizard if you want to view correct source details A new VM is created The source machine's disks are snapshotted/shadow copied, so that they can be copied whilst the OS is still running The source machine's disks are copied to
On the machine where Converter Standalone server runs, browse to the converter-worker.xml file in the following location %ALLUSERSPROFILE%\Application Data\VMware\VMware Converter Standalone\. this contact form For the post . . . Re: "Unable to Obtain Hardware information for the selected machine" POCEH Aug 8, 2014 1:03 AM (in response to bupt_Henry) Unfortunatly the most important log (converter-worker.log) is missing, try to find Try migrating the VM to another ESX Try re-registering the VM in the vCentre inventory Network connectivity problems between the server and client (ie the vCentre that Converter is running from, Unable To Obtain Hardware Information For The Selected Machine Linux
RSS feed Search for: Recent Posts Migrate VM's from Hyper-V 2008 R2 to Hyper-V 2012R2 MDT 2013 - WSUS updates not installing in tasksequence Lync 2010 Standard - 33060 events - Provide write privileges to the network share where the source virtual machine resides. In the Data to Copy pane, select the volumes to copy and click Advanced. have a peek here To restart Converter Standalone worker: Reboot the system or open the Services section in the Microsoft Management Console, find the VMware Converter Worker service and restart it.
If you choose to leave the remote agent on that source and then install Converter Standalone on the same machine, the Converter Standalone installer uninstalls that agent without any warning messages. Converter 5.0.1 Build 875114 Here xxxxxxx is the IP address of the source machine. Note: Microsoft does not support running a PIC HAL on an APIC computer.
Converting standalone VMware sources with a VMDK file greater than 2GB to a hosted destination that resides on a network share that does not support large files, fails If you select Email check failed, please try again Sorry, your blog cannot share posts by email. %d bloggers like this: Home VMware Converter: Unable to obtain hardware information for the selected machine by In such case, the following error messages might appear in the worker log: [01628 warning 'Default'] Partition:Invalid sector magic number. [01628 warning 'Default'] ERROR: Failure during open: Reading disk signature [01628 Vmware Converter Unable To Obtain Hardware Information Linux Converter Standalone does not change PIC HAL to APIC HAL during conversion of Windows source machines If the source to convert is running a Programmable Interrupt Controller (PIC) HAL, Converter Standalone
one project at a time. November 25, 2013 at 8:30 PM Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) Terence Luk Search My Blog Loading... Quick note about regenerating an EXISTING GoDaddy ... http://webinweb.net/unable-to/vmware-converter-unable-to-obtain-hardware-information.html Microsoft Windows Vista or later is installed as a second operating system on the source physical machine and later is removed, but the BCD manager is left on the source machine.
Converter Standalone cannot detect the power state of VMware Workstation or other VMware hosted source virtual machines if they are located on a read-only network share If the source machine is Benefits Convert physical machines running Windows or Linux operating systems to VMware virtual machines quickly and without any disruption or downtime. Obtaining the Software You can obtain the Converter Standalone SDK 5.5 from here. Workaround: First install vCenter Converter 4.2.1 and then install Converter Standalone 5.5.
Creating your account only takes a few minutes. Workaround: Wait for the configuration job to complete before you copy it. You can search the Microsoft Web site for procedures on disabling the UAC depending on the source operating system. Source volumes on top of volume managers other than LVM are not recognized during conversion of powered on Linux machines Converter Standalone recognizes only managed source volumes that run on the
VMware ESXi 4.0 Update 2 slow boot up seemingly st... The following warning message appears: GdmLocalIDisplayFactory: maximum number of X display failures reached: check X server log for errors. Richardson Porto Senior Infrastructure Specialist LinkedIn: http://linkedin.com/in/richardsonporto Like Show 0 Likes (0) Actions 26. In the Computer Management window, select Services and Applications > Services on the left.
My Pages My Twitter My Linkedin Profile My Flickr Page Blog Archive ► 2016 (75) ► December (10) ► November (8) ► October (2) ► September (2) ► August (1) ► I get this message when trying to select the source type in VMWare Standalone Converter 5.0 I tried the VMWare forums and see a lot of suggestions for olderconverter versions most Restart. If the connection port is different from the one that is being used for the already running conversion job, both jobs fail.
vmware-converter-worker-1.log.zip 1.9 K Like Show 0 Likes (0) Actions 21. Note: Care should be taken when this option is enabled and the helper VM network is configured to use a static IP address. as Physical Computer, and click Next In Name or IP Address: enter the source physical machine's IP address (its more reliable than using a name) and in Authentication enter the details