Home > Unable To > Vmware Converter Unable To Obtain Hardware

Vmware Converter Unable To Obtain Hardware

Contents

Join the community Back I agree Powerful tools you need, all for free. In this case, the number of source disks is limited to 27 for ESX and to 23 for ESXi hosts. vmware-converter-worker-1.log.zip 1.9 K Like Show 0 Likes (0) Actions 21. In the Worker/Agent log this issue is identified by the following statement: [#### warning 'Default'] ERROR: [Mntapi_GetFirstBootDisk] more that *one* active volume found. http://webinweb.net/unable-to/vmware-converter-unable-to-obtain-hardware-information.html

Workaround: Recreate the xorg.conf file. Workaround: Create a new virtual machine using the vSphere Client. The number of LVM logical volumes per volume group is limited to 12 for powered on Linux sources During the conversion of powered on Linux machines, Converter Standalone converts LVM volume For more information on how to repair BCD, see the Microsoft knowledge base article Windows no longer starts after you install an earlier version of the Windows operating system in a

Vmware Converter V2v Unable To Obtain Hardware Information For The Selected Machine

While doing P2V conversions with Windows Server 2008 R2; I faced a few problems. I then finally resolved the issue by using Converter 5.0.1 Build 875114. Can you turn worker service logging to 'verbose' (instructions how to do it are available at VMware KB: Increasing the logging levels to verbose for vCenter Converter application components ), *restart In my case it was because the esx server was v. 3.5 and the vcenter server was 2.5.

Get 1:1 Help Now Advertise Here Enjoyed your answer? See the respective Readme files (readme_java.htm and readme_dotnet.htm ) for information about building and using the samples. Presence issues for Microsoft Lync Server 2010 use... Vmware Converter 6 Unable To Obtain Hardware Information Thus, the Converter assumes that the operation has timed out and closes the connection, no matter that the ESX server is still writing to the target disk.

In such cases, after the conversion job is 96-98% complete, the conversion job status changes to Failed and an error message appears. Quick note about P2V with Cold Clone WinPE CD and ... If your source is an APIC computer running a PIC HAL, you must configure the correct HAL on the source machine before starting the conversion. On the machine where Converter Standalone server runs, browse to the converter-worker.xml file in the following location %ALLUSERSPROFILE%\Application Data\VMware\VMware Converter Standalone\.

By default, Converter Standalone has a 20 minute timeout when waiting for the helper virtual machine to start up during Linux P2V conversion This might cause a Linux P2V conversion task Converter 5.0.1 Build 875114 Like Show 0 Likes (0) Actions 25. This is because Windows Server 2008 has a new SAN policy that determines whether a newly discovered disk is brought online or remains offline. Users with limited rights cannot install Converter Standalone on Windows If you are logged in to Windows as a non-administrator user, the following error message is displayed while the InstallShield is

Unable To Obtain Hardware Information For The Selected Machine Hyper-v

For C# developers, the Microsoft Visual Studio project files (.sln) have been included. Create a free website or blog at WordPress.com. Vmware Converter V2v Unable To Obtain Hardware Information For The Selected Machine To view release notes for prior releases of Converter Standalone, click one of the following links: VMware Converter 5.5.1 VMware Converter 5.5 VMware Converter 5.1 VMware Converter 5.0.1 VMware Converter 5.0 Unable To Obtain Hardware Information For The Selected Machine Linux I was trying to run the conversion from a machine that did not support the hardware that I defined for the guest when it was on the origianal Go to Solution

Simon Payne Says: November 27, 2013 at 8:04 AM | Reply I think he means UAC. this contact form None of the vms are interdependent nor do they share any files between them.One datastore is empty, and Ive been trying to move a VM from another datastore to this one, Dan Says: September 2, 2013 at 9:14 PM | Reply The way I got around this was by choosing the remote machine option & IP of 127.0.0.1. The diskpart command prompt appears. (Optional) To list the available disks, enter list disk. Vmware Converter 5.5 Unable To Obtain Hardware Information

Is that a separate physical disk or a partition? Help Desk » Inventory » Monitor » Community » Terence Luk Tackling the daily challenges of technology... For more information on "signature()" go to http://support.microsoft.com/kb/227704. have a peek here Quick note about not being able to mount an ISO as...

VMware ESXi 4.1 show's Intel 82576 Gigabit NIC on ... Vmware Converter Unable To Obtain Hardware Information Linux Current active disk #0, another active disk #1. Depending on the selected source, you can convert it to the following destinations.

fred astaire Says: September 9, 2013 at 1:32 PM | Reply I got to this post looking for a workaround to the same problem.

If your source computer is a PIC computer that runs a PIC HAL, you must update the HAL in the destination virtual machine to APIC HAL after the conversion. To find out which HAL is running, go to Windows Device Manager and select Computer in the list of devices. Converter Standalone remote agent does not notify the user about Converter 3.0.x or 4.0.x remote agents that have been installed on the source system during remote hot cloning process If Converter Vmware Converter 5.0 1 Download After the conversion job is 99% complete, the job status changes to Failed and the following entry is added to the log: FAILED: An error occurred during the conversion: 'Failed to

Quick note about reconfiguring an ESX 4.x server's... ► 2010 (194) ► December (42) ► November (35) ► October (21) ► September (18) ► August (29) ► July (49) My Popular Workaround: Map the network shared folder to the machine where Converter Standalone runs, and select the source from there. Enter inactive. Check This Out To make your system more robust, use the volume label or UUID instead of the block device name.

HP does not control and is not responsible for information outside of the HP Web site. Another alternative is to use local builtin administrator account as this bypasses UAC Leave a Reply Cancel reply Enter your comment here...