TECHNOLOGY IN THIS DISCUSSION VMware 396226 Followers Follow VMware ESXi Join the Community! All rights reserved. In this blog, we will discuss how you can benefit from Office 365 email backup with the Veeam’s new product and try to shed some light on the needs and … In the vmware.log I found "File Not Found" errors from any attempt to start the VM back up. Source
Thanks for the input! 0 Featured Post Save on storage to protect fatherhood memories Promoted by Western Digital You're the dad who has everything. Join & Ask a Question Need Help in Real-Time? Incapsula incident ID: 471000120295112442-1057484243239108807 Home VSphere 5.0 unable to migrate, Unable to access .vmx file by LouisFastener on Aug 13, 2013 at 1:44 UTC | VMware 0Spice Down Next: ESXi VMs I used this vmdk generator to resurrect the missing files:http://www.esxpress.com/tools/wrapgen.php and added the paths to these files back into the .vmx (scsi device section again).
Since this article is too long, I will create second article for the Veeam tasks. If you are using san snapshots then this may have been the reason to use RDM as well dedupe/SIS depending on your SAN functionality. 0 LVL 16 Overall: Level 16 The storage is shared, the esxi host can see the storage, I tried a cold migration and got the same error message.
Help Desk » Inventory » Monitor » Community » Notes from a Sysadmin Virtualization, systems administration, and general geekiness. Unable To Access The Virtual Machine Configuration Invalid Datastore Path It at least explains why your RDM was converted to a VMDK. There is also a /hostname1_2-rdm.vmdk which kind of confuses me, since the RDM that is attached to this VM is 100GB in size, but this /hostname1_2-rdm.vmdk is 50GB in size... Re: Vmotion error - "unable to access the virtual machine configuration: Unable to access File" taits Jan 17, 2008 4:53 PM (in response to acuster) Check the VM log files -
I have three HP hosts at ESXi 5.0.0. Each can see all datastores. 0 Tabasco OP jffnuggets Nov 7, 2013 at 7:59 UTC Seems it's a known issue: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1003795Vmware Unable To Access The Virtual Machine Configuration I was doing the migrations in an effort to bring the ESX hosts up to date with some patches. Virtualization of our servers Virtualize all physical servers on new ESXi hosts and SAN storage. But I'd like to figure out why I can't migrate, or even power on at this point the original VM due to a disk it thinks should be there but isn't.
I've never seen that happen before where a clone converts an RDM to .vmdk so even though it *seems* to be working, I am not sure it is right. The .vmx file had pointers to the destination datastore with the .vmdks identified as the Dmotion ones. Unable To Access File Ds ///vmfs/volumes I am not very experienced at troubleshooting any deeper than the VC / GUI. Virtual Disk 'hard Disk 1' Is Not Accessible On The Host Not sure on your SAN, but in the VNX I had to also make sure that it could see my esxi hosts, so those had to be added in as well.
Re: Vmotion error - "unable to access the virtual machine configuration: Unable to access File" BankTech Jan 29, 2009 9:20 AM (in response to BankTech) In addition to what I this contact form If I recall right this was specific to Dell servers that had flash installed for you to install Esxi on. I did confirm from the SAN side and from ESX side the LUN for that RDM is mapped to both hosts. My Passport Ultra has automatic backup and password protection to keep your cherished photos and videos safe. Clone Virtual Machine Error Caused By File /vmfs/volumes/
myVM-flat.vmdk & myVM.vmdk) went AWOL at some point. As long as you don't change anything in settings you can use new vm as a migrated vm after shutdown old one. 2 Pimiento OP Luis Mendez Nov So then I try and cold migrate the VM to a new host, and to a new datastore. have a peek here Re: Vmotion error - "unable to access the virtual machine configuration: Unable to access File" shunter86 Oct 1, 2009 6:09 AM (in response to BankTech) I am having this issue as
Like Show 0 Likes (0) Actions 4. Vmkernel Log But, this seems to have worked, and the server is online and doesn't have any issues that I can tell right now. Any thoughts on what else to look at would be appreciated.
Creating your account only takes a few minutes. You must also make sure the mapping of that raw LUN is identicle on each ESX host involved in the vmotion. Once the the IDs were the same, no problems Like Show 0 Likes (0) Actions 3. Check This Out If the hostname1_2 disk is being pointed to a deltadisk, then that could be the reason your VM migration does not happen.
Join our community for more solutions or to ask questions. Hassle-free live chat software re-imagined for business growth. 2 users, always free. bgoering, thanks for that link on migrating VMs with an RDM. Otherwise it's the same error as the initial poster.
It had a Snapshot attached to it still. Share This Page Legend Correct Answers - 10 points Request unsuccessful. Our SAN team did not present the LUNS to each host with the same ID. On your original VM, go through settings and see if the disk paths are being pointed to the original vmdk file or to a snapshot.
Incapsula incident ID: 471000120295112442-1617259855051423946 Request unsuccessful. Fill in your details below or click an icon to log in: Email (required) (Address never made public) Name (required) Website You are commenting using your WordPress.com account. (LogOut/Change) You are I want to get rid of whatever it is that is pointing to this file so I can migrate this VM around again, or at the very least power it on. Linux hasn't ever been my strong point.
If you are, you just need to download the Dell esxi image. You need to present the storage to each host, which you can do through the configuration > storage menu on your esxi host. The explanation here provided a place to start looking and find the details to clarify the issue. This can occur when the file in question is on a local datastore, or if SAN storage is not configured properly (read identically) for both the source and target ESX host.
Not sure on your SAN, but in the VNX I had to also make sure that it could see my esxi hosts, so those had to be added in as well. Connect with top rated Experts 14 Experts available now in Live! Thank you for the quick reply! I have no idea what this means, and can't really find any documentation on it that fits this situation.