Error message “Inaccessible boot device”. ldhoore 7 November 2011 at 20:52 (UTC 1) Link to this comment Only virtual machines that are running Windows XP or later can be configured during the conversion process. You can also try running Converter again and selecting "Configure Machine" and select your newly created VM. A few days later I tried to convert a Xen virtual machine running Linux to VMware ESXi, but the conversion failed after just 1% with the following status: FAILED: MethodFault.summary As shown http://webinweb.net/vmware-converter/vmware-converter-error-unable-to-configure-the-destination-virtual-machine.html
Note that these steps only apply to Windows operating systems. BEFORE CONVERSION Confirm that the source server has at least 200 MB free disk space on its system volume. RealWheel 14/01/2011 at 13:23 (UTC 1) Link to this comment Reply I had the same problems. Used VMware Converter 5.0.1. In your inbox. 1229 Redirect Link Contributor Petra Jorgenson is a professional writer with over six years of IT experience.
Hopefully the information in these articles will help you in converting your physical servers to virtual ones. Reduce it if you can. Edit the boot.ini on the newly created VM to make sure the disks are in the proper order.
On Windows XP and 2003 servers make sure the Volume Shadow Copy service is not disabled, by default it should be set to Manual. Double-check to make sure all the entries got added. If you are experiencing a similar issue, please ask a related question Suggested Solutions Title # Comments Views Activity Upgrading Veeam Cloud Connect from 9 to 9.5 3 84 43d VMware Incapsula incident ID: 276000470116381193-522954865791730425 Request unsuccessful.
One point to note here is that if you are converting from IDE disks, then remember to change the disk from IDE to scsi Bryan 18 November 2010 at 00:28 (UTC ConverterDiagnostics20120111095431.zip 221.4 K Like Show 0 Likes (0) Actions 4. Reboot once you have removed them all. greetings Carlos 21/10/2010 at 19:37 (UTC 1) Link to this comment Reply can be a little more specific about it?
The first step is to acquire the necessary licen… Storage Software Windows Server 2008 VMware Disaster Recovery Advertise Here 675 members asked questions and received personalized solutions in the past 7 Confirm the installation of the software to proceed with the conversion.Enter the server address and login credentials for the ESX/ESXi or Hyper-V Server. If the source system is inside a Distributed Resource Schedule (DRS) cluster that vCenter Server controls, DRS Power Management (DPM) will turn off the ESX/ESXi host that vCenter Converter is working In the second half of this two-part series, I'll explain how to import an existing virtual machine (VM) into an ESX/ESXi Server.VMware vCenter Converter supports several different kinds of virtual machines.
They can also cause conflicts when trying to set your new network adapter's IP address to the same address of the source server. This service does not need to be running for Converter to work. Thanks. Here's a look back at ...
The conversion finished without error but VM is not starting. Re: Error: Unable to remove the destination virtual machine Plamen Jan 11, 2012 6:40 AM (in response to gfdos) Q1: If a cloning fails, converter deletes the destination VM in order probably should have... Source Use .vmx for virtual machines created in VMware.
Also ensure that you are using the correct version of Converter, which supports 2003 SP2. AK vmware-converter-server-1.log 0 Comment Question by:Akulsh Facebook Twitter LinkedIn https://www.experts-exchange.com/questions/28531825/P2V-failed-Unable-to-reconfigure-the-destination-virtual-machine.htmlcopy LVL 118 Active 1 day ago Best Solution byAndrew Hancock (VMware vExpert / EE MVE) I would complete a simple P2V After careful reading, I found out that VMware ESX 4.1.0 isn't listed as a supported destination!
Remove all unnecessary hardware, including floppy drives and serial, parallel and USB ports. What is the size of each disk and how much of each diskspace is used? 3. I didn’t notice it while the conversion was running, but right at the end of the job, a warning was logged…”virtual machine reconfiguration failed”. Join Now For immediate help use Live now!
The reconfiguration task that failed on the conversion indicated that VMware was unable to inject the driver and registry keys into the VM post conversion…ah yes, the odd-ball configuration. Get 1:1 Help Now Advertise Here Enjoyed your answer? Note that if you're importing a VM from Microsoft Virtual PC, you should remove the Virtual PC Additions from the machine, as they can interfere with the conversion process.Enter the login http://webinweb.net/vmware-converter/vmware-converter-unable-to-configure-the-destination-virtual-machine.html I just had to figure out how to make those changes post-conversion.
To do this, simply use a working VM as a helper and add an additional virtual hard disk. Enter a new name for the destination machine or use the default name. ABOUT THE AUTHOR: Eric Siebert is a 25-year IT veteran with experience in programming, networking, telecom and systems administration. Verify you are using the proper SCSI controller for your virtual disk (BusLogic or LSI Logic).
Incapsula incident ID: 276000470116381193-319323259333247729 MenuExperts Exchange Browse BackBrowse Topics Open Questions Open Projects Solutions Members Articles Videos Courses Contribute Products BackProducts Gigs Live Courses Vendor Services Groups Careers Store Headlines Website Join the community of 500,000 technology professionals and ask your questions. Jorgenson is working on obtaining her MCITP certification. Conduct power cycling tests to proactively monitor systems and identify ...
Any help. Please type your message and try again. 6 Replies Latest reply: Jan 11, 2012 8:11 AM by Plamen Error: Unable to remove the destination virtual machine gfdos Jan 11, 2012 6:13 You have exceeded the maximum character limit. I attached the vmdk to a helper VM to access the files.
Step 2 of 2: You forgot to provide an Email Address. Wondering if unselecting "Reconfigure destination virtual machine" will do the trick, or should I change the name and IP temporarily.