Home > Warning Unable > Warning Unable To Get Ldom Variable Updates

Warning Unable To Get Ldom Variable Updates

Contents

Workaround: If the domain fails to boot, do one of the following: Stop and start the impacted domain while the system is in elastic mode Configure the Power Management mode from If an SVM volume built on top of a disk slice that contains block 0 of the disk is exported as a full virtual disk, then a guest domain is unable Workaround: Set ip_ire_min_bucket_cnt and ip_ire_max_bucket_cnt to larger values, such as 32, if you have 8 interfaces. Workaround: Use this command instead: uadmin 2 0 Or, always run with auto-reboot? have a peek here

http://mail.opensolaris.org/mailman/listinfo/caiman-discuss _______________________________________________ caiman-discuss mailing list caim...@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/caiman-discuss Fri 03:12:29 | cache-2.a | 0.13 seconds | © 2007-2014 MarkLogic Corporation. Use is subject to license terms. This can also impact the zone's dedicated CPU feature. Note РThe examples in this section are what happens on UltraSPARC T1 based platforms.

Ldom Stuck In Transition

Starting and Stopping SunVTS Multiple Times Can Cause Host Console to Become Unusable Bug ID 6549382: If SunVTS is started and stopped multiple times, it is possible that using the console OpenBoot PROM Variables Cannot be Modified by the eeprom(1M) Command When the Logical Domains Manager is Running Bug ID 6540368: This issue is summarized in Logical Domains Variable Persistence and affects Subsequently, a new CPU is dynamically added. If you are concerned about Logical Domains variable changes, do one of the following: Bring the system to the ok prompt and update the variables.

Any access to the virtual disk fails with an I/O error. Cryptographic DR Changes Incompatible With Pre-LDoms Firmware Bug ID 6713547: Cryptographic dynamic reconfiguration (DR) changes are incompatible with firmware that is prior to LDoms software releases. Possible Issues After a Failed add-vdisk Command Bug ID 6854189: If adding a virtual disk to a running guest domain fails, the guest domain might show messages like the following after Ldom Logs Changes to OpenBoot PROM Variables With Nondefault LDoms Configuration Do Not Persist (CR 6593132) If an LDoms variable is set to a nondefault value when an LDoms configuration is saved to

Use the ldm list-devices -a mem command to see what memory is available and how it is used. This is a result of the Logical Domains Manager's constraint database not being kept in sync with the change in configuration. This glitch is harmless, and the domain is fully operational. This is a result of the Logical Domains Manager's constraint database not being kept in sync with the change in configuration.

Power Cycle the System Shut down and unbind all the non-I/O domains. Ldom Networking Issues Domain Migration in Elastic Mode Is Not Supported Domain migrations are not supported for a source or target machine in elastic mode. If you were unable to preserve the constraints database, do not populate the control domain with a constraints database that does not match the running configuration. See the path_to_inst(4) man page.

Solaris Ldom Commands Cheat Sheet

So, when domaining is not enabled, if you want a variable update to persist across a reboot into the same factory-default configuration, use the eeprom command. Stop and unbind the domain on the target, and fix the vdsdev. Ldom Stuck In Transition After upgrading or repositioning the CMP modules, follow the instructions in “Node Reconfiguration” in Sun SPARC Enterprise T5440 Server Product Notes, which are in the Sun SPARC Enterprise T5440 Server Documentation Ldm List Flags -t---- Power Off a System With Multiple Active Domains Shut down and unbind all the non-I/O domains.

Refer to System Requirements and Recommendations in Solaris 10 5/09 Installation Guide: Planning for Installation and Upgrade. navigate here Spurious dl_ldc_cb: LDC READ event Message Seen When Rebooting the Control Domain or a Guest Domain Bug ID 6846889: When rebooting the control domain or a guest domain, the following warning Fix the vdsdev. Fault Management There are several issues associated with FMA and power-managing CPUs. Failed To Connect To Logical Domain Manager: Connection Refused

You might have encountered this problem if the progress percentage remains constant for several minutes. I/O Domain or Guest Domain Panics When Booting From e1000g Bug ID 6808832: You can configure a maximum of two domains with dedicated PCI-E root complexes on systems such as the The system is unable to properly reestablish a connection following an SC reset. Check This Out Unable to bind memory; limit of 31 segments reached Bug ID 6841421: Under certain memory configurations, creating a guest domain might fail with this error message: Unable to bind memory; limit

Issue the ldm rm-vdsdev command to remove the errant virtual disk service device. Ldom Cannot Be Unbound Because It Has Active Clients Pseudonyms for PCI Buses on Sun SPARC Enterprise T5440 Systems Are Not Correct Bug ID 6784945: On a Sun SPARC Enterprise T5440 system, the pseudonyms (shortcut names) for the PCI buses If there is a dynamic resource managment (DRM) policy in effect for the domain at the time of the migration, the Logical Domains Manager might begin to add CPUs.

For more information, refer to I/O Domains and PCI EXPRESS Buses in Logical Domains 1.2 Administration Guide.

Add more file systems of adequate capacity. The control domain is not affected, and there is no indication that the guest domain panicked on the control domain console. Previous: Related SoftwareNext: Resolved Issues © 2010, Oracle Corporation and/or its affiliates Documentation Home > Logical Domains 1.2 Release Notes > Chapter¬†1 Logical Domains 1.2 Release Notes > Known Issues > Not Enough Free Memory Present To Meet This Request. Workaround: Only net-install on guest domains that each have their own console group.

Warning: Console connection forced into read-only mode Recovery: Reset the SC using the resetsc command. Reboot the domain hosting the virtual switch in question. This removal of the device ID of the virtual disk can cause problems to applications attempting to reference the device ID of virtual disks. http://webinweb.net/warning-unable/warning-unable-to-get-configuration-variable-updates.html If the problem has occurred on the primary domain, do the following: Start a delayed reconfiguration operation on the primary domain.# ldm start-reconf primary Assign the desired amount of memory to

Does it support ALOM? panic[cpu0]/thread=180e000: XC SPL ENTER already entered (0x0) Impact: Because the panic occurs very early in the boot sequence, it has no impact on applications or file systems because they have not To enable core disable operations to be performed when the system is in elastic mode, remove the cryptographic units that are bound to the domain. Then migrate the guest domain.

Behavior of the ldm stop-domain Command Can Be Confusing Bug ID 6506494: There are some cases where the behavior of the ldm stop-domain command is confusing. # ldm stop-domain -f ldom