Home > Warning Unable > Warning Unable To Update Ldom Variable

Warning Unable To Update Ldom Variable

Contents

Issue the ldm add-vdsdev command to correct the physical path to the volume. This issue does not occur if all the vnets are connected to a single vsw. Connected to localhost. make sure names can be resolved. Check This Out

Use is subject to license terms. Unfortunately, am still not able to configure jumpstart. Recovery: Use the ldm stop-domain and ldm start-domain commands to stop and start the guest OS. If the OS supports virtual I/O dynamic reconfiguration, and the incorrect virtual disk in not in use on the domain (that is, it is not the boot disk and is unmounted),

Failed To Connect To Logical Domain Manager: Connection Refused

You can also manually edit the /etc/path_to_inst file. whoami: no domain name Here is the snoop dump from the control domain darkstar -> ldom1 NFS R GETATTR3 OK darkstar -> ldom1 NFS R GETATTR3 OK darkstar -> ldom1 NFS Has > anyone seen the message below? > Thanks > SunOS Release 5.10 Version Generic_142900-03 64-bit > Copyright 1983-2009 Sun Microsystems, Inc.  All rights reserved. > Use is subject to license Thank you for sharing.

Service Processor and System Controller Are Interchangeable Terms For discussions in Logical Domains documentation, the terms service processor (SP) and system controller (SC) are interchangeable. Disk PathsIf a disk device listed in a guest domain's configuration is either non-existent or otherwise unusable, the disk cannot be used by the virtual disk server (vds). mailto:[email protected],5.11-0.111:20090418T200225Z 3. Ldom Logs During the reboot, you will see messages similar to this: NOTICE: mddb: unable to get devid for 'vdc', 0x10 These messages are normal and do not report any problems.

If a workaround and a recovery procedure are available, they are specified. Warning: Console connection forced into read-only mode Recovery: Reset the SC using the resetsc command. Hang Can Occur With Guest OS in Simultaneous Operations Bug ID 6497796: Under rare circumstances, when a Logical Domains variable, such as boot-device, is being updated from within a guest domain However, the Logical Domains Manager does not emit any warning or error when the domain is bound or started.

So you can tell, I did get booted and answered all the install questions. Ldom Networking Issues However, the current versions of Logical Domains Manager can only support up to 31 memory segments for each guest domain. So here's what I would start out with and why.4 vcpu's - This is based on keeping the 4 threads per core aligned. If a migration is underway while in performance mode and the power management policy is set to elastic mode, the policy switch is deferred until the migration completes.

Ldom Stuck In Transition

Logical Domains Manager Can Take Over 15 Minutes to Shut Down a Logical Domain Bug ID 6742805: A domain shutdown or memory scrub can take over 15 minutes with a single panic[cpu0]/thread=180e000: XC SPL ENTER already entered (0x0) Impact: Because the panic occurs very early in the boot sequence, it has no impact on applications or file systems because they have not Failed To Connect To Logical Domain Manager: Connection Refused Workaround: Restart the vntsd SMF service to enable connections to the console: # svcadm restart vntsd Note – This command will disconnect all active console connections. Solaris Ldom Commands Cheat Sheet I then installed all the patches.

NOTE: This is a bug when installing from DVD with a disk with zfs already on it. his comment is here Recovery: The logical domain should display the correct state upon the next reboot. Workaround: SVM volumes exported as a virtual disk should not be built on top of a disk slice that contains block 0 of the disk. What you will need to do is unconfigure SUNWjess ( which hardens the systems ) and once jumpstart setup is complete just apply securiy hardning. Ldm List Flags -t----

Then, use the svcadm restart ldmd command to restart the Logical Domains Manager and to resume normal operations. Workaround: Avoid booting many domains simultaneously. I did this by mounting the DVD and running:[email protected]:/cdrom/sol_10_1106_sparc/s0/Solaris_10/Tools>setup_install_serverThen I did a few short cuts knowing this isn't the best or recommended way to jumpstart a server. http://webinweb.net/warning-unable/warning-unable-to-get-ldom-variable-updates.html On Ultra SPARC T2 based servers, such as the Sun SPARC Enterprise T5120 and T5220 servers, assign a Network Interface Unit (NIU) to the logical domain.

I increased the control domain to have 3GB and I was able to squeak through the jumpstarting of the guest domain. Ldom Cannot Be Unbound Because It Has Active Clients Its not uninstalling SUNWjess, but unconfiguring SUNWjess to unharden the system. ( This is assuming that your jumpstart server is in control domain ). This problem prevents UltraSPARC T1 based systems running old firmware from using cryptographic hardware.

OpenBoot PROM Variables Cannot be Modified by the eeprom(1M) Command When the Logical Domains Manager is Running Bug ID 6540368: This issue is summarized in Logical Domain Variable Persistence and affects

Fix the vdsdev. Posted by INIT07 on November 10, 2008 at 09:08 PM CST # INIT07, Glad this helped. If a workaround and a recovery procedure are available, they are specified. Not Enough Free Memory Present To Meet This Request. Workaround: SVM volumes exported as a virtual disk should not be built on top of a disk slice that contains block 0 of the disk.

Explicit Console Group and Port Bindings Are Not Migrated Bug ID 6781589: During a migration, any explicitly assigned console group and port are ignored, and a console with default properties is However, ldmconfig permits you to continue to use the disks that are in /ldoms/disks to deploy the configuration. If auto-reboot? http://webinweb.net/warning-unable/warning-unable-to-get-configuration-variable-updates.html to return to ALOM.

Even though the stop operation has timed out, the process continues to shut down the logical domain in the background. Halt the primary domain.